Skyartec FREE X Skyview in Red color

       FREE X Skyview specification:

• Motors : 4pcs of 2212-1050KV Brushless Motor;
• Propeller size: out of the box it is equipped with 9 inch blades, but also supports 10 inch propellers;
• ESC : 15AX Brushless ESC;
• Radio receiver : Free X Receiver;
• Transmitter : 7 channel 2.4Ghz Free X remote controller;
• Battery : 3s 11.1V 3000mAh Li-Po;
• Fight Control Board : Onetouch 4;
• GPS flight control board : FREE-X GPS module;
• Width and length: 280 mm;
• Height: 191 mm;
• Diagonal: 396 mm;
• Colors: red;
• Weight: 840g (Include the Li-Po battery).

Skyartec Free X flight parameters:

• Fight time: up to 15 minutes;
• Max Stern Rudder Angle Speed : 150 °/s
• Max Angle of Inclination : 45°
• Max Lifting Speed : 3.5m/s
• Max Flight Speed : ≤30km/h

Free X transmitter specs:

• Remote control frequency : 2.4GHz frequency hopping;
• Number of channel : 7;
• Output Power : < 100mW;
• Current consumption : < 230mA(100mW/h);
• Output Pulse : 1000-2000mS (SUB TRIM is 1500);
• Outdoor control distance : up to 1 km.

 Skyartec FREE X Skyview package includes:

• Free X RTF Quadcopter, tweaked and tested;
• 4pcs of balanced high performance propellers (two CW and two CCW Blades);
• USB Cable / USB Dongle for firmware upgrade
• 2.4 GHz 7Ch Remote controller
• 3s 11.1V 3000mAh Lithium Polymer battery;
• Balance battery charger;
• Optional Gimbal.
• 

  • Ready to fly right out of box after a simple compass calibration .
  • No need for any complex preflight settings, no programming and parameter tweaking needed. Its Ready to fly right out of box after a simple compass calibration and One touch Gyro initialization with supplied USB Dongle.

  

  • Onetouch 4 Quadcopter Control Board
  • Onetouch 4 controller is extremely easy to setup, with the included software any one can adjust the parameters to his flying requirements.

  

  • Two flight modes.
  • Offers 2 very beginner friendly Flight modes: 1.The Attitude and Altitude Hold mode: Quadcopter will hold its altitude and attitude once all the sticks are centered.
    2. The GPS Position hold mode: Quadcopter will hold its Altitude, Attitude and GPS position once all the sticks are centered. It¢s the perfect feature for beginners to learn to fly as this gives them plenty of time to build their orientation and flying confidence.

  

  • IOC Flight Mode (Intelligent Orientation Control)
  • When IOC switch is turned on left and right aileron direction remains the same even if FreeX is flying with the nose facing  you.
  • Very helpful for the beginners.

   

  

  • Auto-return Function (with the world¢s first full-time all channel active control during RTH)
  • FreeX SkyView Quadcopter with FreeX flight controller offers very precise and reliable Auto Return to home both on Demand and on failsafe.

  

   

  • Pilots can choose from two modes upon control signal lose: 1.Auto Return to home .2. Hover at last known position
• 

  • Low voltage protection
  • When the voltage is lower than the set voltage in FreeX parameter control software, the LEDs on the QuadCopter will blink to inform the pilots of low voltage on battery and pilots can easily fly back and land the Quadcopter before battery totally runs out of power.

  

   

  • High quality balanced, Self-tightening propellers on motors are very easy to install and direction markings on props and Quadcopter arms will guide even beginners to install them correctly on the motors. 

  
•  

  • Safety Protocol Algorithm
  • FreeX has a special SPA (Safety Protocol Algorithm) that checks when you power  up the electronics, 1)Transmitter - receiver link established when the red Led  in the back is on. 2) Compass active when blue Led is on, when pointing to magnetic North. 3) Green Led on when GPS is healthy and blinking when 6 Satellites are located. 

  

  • High Intensity LED Lights, To Aid Orientation During Flight
  • there are some high intensity LED indicators which are used to help you to the orientation during flight.

  

  • Fuselage structure
  • The fuselage structure is stronger than other brands 70% , resistant crash and impact. Diagonal dimension is 38 cm. The standard configuration is 9 inches propeller, and support 10 inch propeller.

  

  • Full CNC aluminum alloy brushless gimbal (Optional)
  • Full CNC aluminum alloy, lightweight, two-axis brushless gimbal for GoPro 3 Cameras, Specially designed for GoPro 3 cameras.Easy to install, plug and play. No complex setup or tweaking parameters for Gimbal. Just install the GoPro 3, and power it up to use.

  

  • 2.4 GHz 7Ch Transmitter
  • Transmitter has all the switches labeled according to the flight modes and are very easy to be located. Gimbal up and down motion control is established trough the potentiometer on the right side of the transmitter.
  • Fail safe mode is activated when signal is lost due to out of range or signal loss and Return To Land is activated by the flight controller.       
  • Stick calibration can be performed.
  • Transmitter range is 1Km.